Oil & Fluid Service Tools
11pcs Oil Filter Socket Set
An 11-piece oil filter socket set in A3 steel with electrophoretic paint finish, listed in sizes from 65/67 mm to 100 mm, with an adapter for 3/8″ or 1/2″ square drive wrenches.
PRODUCT RANGE
Automotive Repair, Specialty & Hand Tools
Explore seven categories of automotive repair, specialty and hand tools for distributors, importers and aftermarket brands, with wholesale, OEM & private label, and custom development support.
- CATEGORIES
- 7 core tool categories
- SOURCING
- Wholesale · OEM & Private Label
- CUSTOM DEVELOPMENT
- From drawings, samples or requirements
Product Categories
Browse the Range by Category
Seven categories covering the repair and maintenance jobs a workshop handles every day. Open a category to see the tools in that line.
Brake Service Tools
Caliper wind back kits, brake bleeder kits, brake line flaring tools, drum brake tool sets and brake cylinder hones.
Engine Service Tools
Cylinder hones, piston ring compressors, valve stem seal tools and belt tensioner wrenches.
Testing & Diagnostic Tools
Compression testers for petrol and diesel engines, cooling system pressure testers and circuit testers.
Oil & Fluid Service Tools
Oil filter wrenches, oil filter sockets and fluid filling and transfer tools.
Body, Trim & Glass Tools
Windshield and glass removal tools, trim and panel removal sets, and clip pliers.
Suspension, Steering & Bearing Tools
Coil spring compressors, ball joint separators, bearing pullers, press and pull sleeve kits and inner tie rod tools.
Automotive Specialty Hand Tools
Hose clamp pliers, CV boot clamp tools, thread repair kits, inspection mirrors and magnetic pick-up tools.
All products
52 products
View product
Suspension, Steering & Bearing Tools
21pcs Ball Joint Puller Kit
A 21-piece ball joint puller kit for removing ball joints, disassembling and assembling U joints, and removing and installing brake anchor pins, working comprehensively with a wide range of vehicles.
Automotive Specialty Hand Tools
Heavy-Duty Tailpipe Cutter
Heavy-duty tailpipe cutter in 65# manganese steel, Q235 and PVC, 501.3 g, for cutting iron pipes, copper pipes and PVC pipes, but not stainless steel pipes.
Automotive Specialty Hand Tools
Torque Angle Gauge
A 1/2″ drive torque angle gauge, calibrated in degrees, used to gauge the degree of turn when fasteners are to be tightened further after torque loads are applied.
Oil & Fluid Service Tools
Drain Plug Tool Kit
A drain plug tool kit in nylon and 45# steel for use on VW, AUDI and PORSCHE, removing or installing the drain plug with a single half turn.
Brake Service Tools
Brake Spring Pliers
Brake spring pliers in carbon steel, 12″ long and 326 g, for removing and installing the spring from the anchor stud.
Brake Service Tools
Car Disc Brake Pad Spreader Separator
A car disc brake pad spreader separator in carbon steel, 17 cm, for fitting disc brake pads across a range of vehicles including Alfa, Ford, Nissan, GM (Vauxhall/Opel), Peugeot and Renault.
Engine Service Tools
Piston Ring Groove Cleaner
A piston ring groove cleaner for removing carbon and glaze deposits from piston ring grooves, suitable for pistons between 51-127 mm, supplied with three cutter heads.
Testing & Diagnostic Tools
TU-1 Vacuum & Fuel Pump Pressure Test Gauge Set
A TU-1 vacuum and fuel pump pressure test gauge set for testing mechanical and electrical fuel pumps, with a 3-1/2″ color-coded gauge reading pressure up to 10 PSI and vacuum up to 28″ HG.
Automotive Specialty Hand Tools
O-Ring and Seal Remover Set
An O-ring and seal remover set in 40# steel, PP and TPR for removing old O-rings without damaging or scratching automotive parts, with two spoon-tipped and two contoured-tipped picks.
Suspension, Steering & Bearing Tools
CV Joint Assembly Removal Tool Kit
A CV joint assembly removal tool kit in carbon steel for separating the CV joint from the axle without removing the drive shaft, with a 30 mm diameter and a 248 mm length.
Automotive Specialty Hand Tools
14pcs Metric Tap and Die Set
A 14-piece metric tap and die set in carbon steel and alloy tool steel, covering M3 to M10, with a die handle and an M3-M12 tap wrench.
Page 1 of 5
Sourcing Options
Choose How You Want to Source
Most buyer programs follow one of these three routes. Tell us which fits and we can review the details from there.
01
Wholesale Supply
Source suitable tools from the existing range for distribution, retail and workshop supply. Send your item list and estimated quantities, and multiple categories can be reviewed in one quotation.
02
OEM & Private Label
For suitable existing models, logo, packaging, color and other branding requirements can be reviewed. Samples or specifications are confirmed before production where required.
03
ODM & Custom Development
Start from a drawing, sample, reference image or a new tool requirement. Feasibility, manufacturing options and the next development step are reviewed before quotation and sampling.
CUSTOM SOURCING & DEVELOPMENT
Have a Tool to Source or Develop?
Start with an existing tool, drawing, reference image, physical sample or a clear repair requirement. Tell us what you need and we'll review the most practical sourcing or development route.
connie_fang@coziness.cn
Phone / WhatsApp
+86 13857891035